Memtech SC3500 Betriebsanweisung

SC3500 3.5” Solid State SCSI Drive User Guide 80-03-00032 Revision 1.3 March 8, 2005 Memtech SSD Corporation 7628 Las Positas Road Livermor

SC3500 User Guide Ver 1.3 March 8, 2005 Page 10 of 28 3.3.4 Format Unit Command – 04h The FORMAT UNIT command formats the medium into initiator

SC3500 User Guide Ver 1.3 March 8, 2005 Page 11 of 28 3.3.5 Read (6) Command – 08h The READ (6) command requests that the SC3500 transfer data

SC3500 User Guide Ver 1.3 March 8, 2005 Page 12 of 28 3.3.7 Inquiry Command – 12h The INQUIRY command requests that information regarding param

SC3500 User Guide Ver 1.3 March 8, 2005 Page 13 of 28 Standard Inquiry Data Format Please refer to the SCSI specification for further details o

SC3500 User Guide Ver 1.3 March 8, 2005 Page 14 of 28 3.3.8 Reserve Unit – 16h The RESERVE command is used to reserve a logical unit or, if the

SC3500 User Guide Ver 1.3 March 8, 2005 Page 15 of 28 3.3.10 Mode Sense The MODE SENSE (6) command provides a means for a target to report param

SC3500 User Guide Ver 1.3 March 8, 2005 Page 16 of 28 3.3.11 Send Diagnostics – 1Dh The SEND DIAGNOSTIC command requests that the SC3500 perfor

SC3500 User Guide Ver 1.3 March 8, 2005 Page 17 of 28 3.3.13 Extended Read (10) – 28h The READ (10) command requests that the target transfer d

SC3500 User Guide Ver 1.3 March 8, 2005 Page 18 of 28 3.3.15 Erase Command Erase CDB The ERASE (10) command requests that the target erase the

SC3500 User Guide Ver 1.3 March 8, 2005 Page 19 of 28 4. GENERAL SPECIFICATIONS Interface SCSI Compatibility ANSI X3.131-1994 SCSI Device Type

SC3500 User Guide Ver 1.3 March 8, 2005 Page 2 of 28 Table Of Contents 1. HIGHLIGHTS ...

SC3500 User Guide Ver 1.3 March 8, 2005 Page 20 of 28 5. JUMPER CONFIGURATION 5.1 Jumper and Switch Locations The following diagrams show the un

SC3500 User Guide Ver 1.3 March 8, 2005 Page 21 of 28 5.2 SCSI ID Selection The SC3500 can use any of the 8 SCSI IDs available on the SCSI bus,

SC3500 User Guide Ver 1.3 March 8, 2005 Page 22 of 28 5.5 Termination Power The SC3500 can supply termination power to the drive and cable by set

SC3500 User Guide Ver 1.3 March 8, 2005 Page 23 of 28 6. INSTALLATION 6.1 Default Configuration By default, no jumpers are installed on the jumpe

SC3500 User Guide Ver 1.3 March 8, 2005 Page 24 of 28 termination enabled. Failure to comply with this requirement may cause erroneous operation

SC3500 User Guide Ver 1.3 March 8, 2005 Page 25 of 28 7. MECHANICAL DRAWINGS The following are mechanical drawings for the SC3500. All mounting

SC3500 User Guide Ver 1.3 March 8, 2005 Page 26 of 28 Fig 7: SC3500 Bottom View

SC3500 User Guide Ver 1.3 March 8, 2005 Page 27 of 28 8. TROUBLE SHOOTING GUIDE The following is a list of possible error indicators or message

SC3500 User Guide Ver 1.3 March 8, 2005 Page 28 of 28 9. APPENDIX 9.1 Contact Information For Technical Support or Warranty Repair information, p

SC3500 User Guide Ver 1.3 March 8, 2005 Page 3 of 28 1. HIGHLIGHTS • 36864 Mbyte uncompressed capacity • Full -40oC to +85oC operating temp ran

SC3500 User Guide Ver 1.3 March 8, 2005 Page 4 of 28 3. GENERAL DESCRIPTION 3.1 SCSI Interface An intelligent SCSI controller from Qlogic, the FA

SC3500 User Guide Ver 1.3 March 8, 2005 Page 5 of 28 The implemented messages on the SC3500 are as follows: 1. Command Complete 00h Generated

SC3500 User Guide Ver 1.3 March 8, 2005 Page 6 of 28 3.2.2 SCSi Connector Pinout The following shows the pin connections for the SCSI connector

SC3500 User Guide Ver 1.3 March 8, 2005 Page 7 of 28 3.3 SCSI Commands 3.3.1 Test Unit Ready Command – 00h Test Unit Ready CDB The TEST UNIT

SC3500 User Guide Ver 1.3 March 8, 2005 Page 8 of 28 3.3.3 Request Sense Command – 03h Request Sense CDB The REQUEST SENSE command requests t

SC3500 User Guide Ver 1.3 March 8, 2005 Page 9 of 28 Sense data format